Danika used leather from a purse that she bought at a thrift store to use as the cover. Heavy weight drawing paper was used for the journal pages. She said sewing is easier if you use waxed linen thread. You will need two needles to sew this book.

Step by step photos can be seen by going to the Read more >.

Place the leather cover / wrapper on a flat work surface. Next place two signatures of folded drawing paper as illustrated above.

Thread needles onto both ends of a long length of thread.

Both signatures should have holes punched in this pattern. At the top of the fold you need two holes about a half inch apart. For this spine pattern, you need to make 6 holes on the spine of each signature. You will start sewing inside the SECOND hole of the second signature.

Lay both signatures on the leather cover. Notice that holes have been already been punched into the leather cover. Remember that this layout allows has a longer piece of leather on the right side. This extra portion is going to be used as a wrapper to close the journal once it is finished.

Move them closer together in order to grab both signatures and to start sewing.

If you are right handed, start on the signature that is on the right. It can be done from the left if you are left handed. Remember (this is very important) that you will start the sewing at the second hole from the top.

In this photo she is grabbing both signatures. However the next step only requires that you thread one needle through the second to the top hole. It is very important to start from inside the fold at the second hole. The needle and thread only pass through the paper at this point. Do not thread the needle through the leather at this stage.

Once the first needle has been threaded through the right side signature, move the needle over the the second hole from the top of the left side signature. Thread it from the spine side.

Here you can see the front of the needle passing through the second hole of the left side signature.

Just a reminder that the thread is been passed through the second hole of the left and right side signatures but not through the leather. Pull the needle and thread so that the length of the middle of the thread’s length is split evenly between the two signatures.

This is an inside view of the left side signature.

You now have one thread through both signatures. Each signature has one needle. At this stage, you want to find the needle that is in the right signature and thread the needle into the top hole as illustrated above.

Pull the thread so that it is tight. Remember to keep the length of the thread even on both sides. You need length of thread to sew both signatures.

Once the thread is pulled tight on the right side signature, you will pass the needle and thread through the top hole of the leather wrapper.

On the left side signature, repeat the step by moving the thread and needle through the top hole.

This photo illustrates the sequence for the thread and needle on the left side signature.

The portion of the image with the needle is a bit out of focus, but it illustrates how the needle and thread are passed through the leather wrapper from each signature. At this point the two signatures are now being sewn to the wrapper with the single length of waxed linen thread.

The thread is pulled tight and the two signatures are aligned on the top of the wrapper.

This image illustrated the view from the spine. Notice that the thread passed through the inside of the fold out through the spine at the top hole.

Next the needles and thread are sewn back into the signatures at the second hole.

This is the point of the binding where the chris-cross decorative stitch begins. Start with the thread from the inside of either signature and thread the needle from the inside out at the next hole (3rd hole).

Once the thread is pulled tight, the needle is moved to the top left stitch to form a diagonal line.

The same needle and thread are returned to the same hole and inserted back into the the hole that it came from.

The needle and thread are brought back into the same hole and the same signature. Then they are left alone while you move over to the other signature with the other needle.

Next, grab the needle in the left signature and thread the needle out of the thrid hole from the inside.

Once the needle has been pulled tight, slide it under the diagonal stitch as illustrated.

The needle should pass under the thread and then should hook in at the top stitch of the opposite signature to create a diagonal line with the thread. The first upward stitch should go under the diagonal stitch and then on the down one it can stay above the stitch. You are simply trying to make a cross over design or pattern. Once you complete this side, you should have completed one section of both signatures. You simply continue this pattern, by sewing one section at a time for each signature until you reach the bottom of the book. To tie off, simply tie a knot on the inside of the last sewing hole.

A closer view of the stitched pattern on the spine of the finished book.

View of the full wrapper.

This inside view shows the thread as it is tied off at the bottom of the signature. You will need to tie down the thread inside of both signatures.

Step one – Load Dreamweaver and go to the Site menu and scroll down to the new site selection.

Step two – You can title your site any name that you like. This is simply the file name, it is not the web site name. Type in the web address that is in your email where it says “What is the HTTP address of your site?” Select “Next”

Step three – Select no for using server technology and then Select “Next” at the bottom of the window. Select “Next” at the bottom of the window.

Step four – Select “Edit Local copies on my machine” for this step. The second window is asking you for a location on your computer to store your files. Click on the folder icon that is located on the right side of the window and navigate to a location of your choice. Select “Next” at the bottom of the window.

Step five – Fill in these sections with your information. In the top window select FTP as your choice. Use the user name and pass word that was given to you, not your UW net id. You can hit the “Test connection” button to see if it connects with the server. Then Select “Next” at the bottom of the window.

Step six – Selected “No, do not enable check in and check out”. Select “Next” at the bottom of the window.

Step seven – Select done.

1 – please explore typographic treatments for your domain name. After class I went to google and I typed in the search field “design blog”. You should do the same and surf around looking at as many design related sites as you can find to get a feeling for type treatments and for the types of names other designers are using. Keep a list of the urls that you visit and be prepared to share them. You can pull them up on the computers in class.

2 – Are you familiar with excel? I suggest you start a new file and call it something like “computer workstation costs.” On one column, start listing all the hardware that you have or hardware that you wish to purchase in order to have a design workstation. Then list the software. Gather prices. Do not use DoIT’s site for pricing as those prices are student prices. In this excel sheet add the cost of buying a domain name and a basic hosting service package with the name of the company.

3 – did I forgot anything?Have a good weekend – Jim